The TAPPI Standards regulations require public review of standards that are up for ballot. TAPPI members can view any drafts that are in ballot by logging in to the TAPPI web site (www.tappi.org), clicking on "My TAPPI," and then clicking on the "Standards Public Draft Review" link on the left side of the page. If you would like to review and comment on any draft and are not a member of the corresponding Standard-Specific Interest Group (SSIG), you may view the draft on line or you may request a copy of the draft being balloted by writing to standards@tappi.org. TAPPI members may join SSIGs as permanent members; go to the Subject Category page to download forms for this purpose. Nonmembers of TAPPI may join any SSIG as a voting member; to do so, send a message to standards@tappi.org to receive a copy of the draft and a ballot.

Listed below are TAPPI Standards that have recently gone out for ballot to the corresponding Standard-Specific Interest Group (SSIG). The date in parentheses is the closing date for voting.

T New (WI 3028) "Roughness of paper and paperboard, stylus (Emveco sharp tip-type) method)" (May 3, 2013)

T 236 "Kappa number of pulp" (May 13, 2013)

T 210 "Sampling and testing wood pulp shipments for moisture" (May 13, 2013)

T 577 "Score bend test" (May 30, 2013)

 

Getting started is easy. Do you have just a general idea for a standard, or are you farther along and have a substantial draft? If you just have a general idea for a standard or TIP, complete the New Idea Submission Form. TAPPI will review your idea and identify an appropriate committee or group to work on your suggestion. If you are further along, send an initial draft to standards@tappi.org. From there, the TAPPI Standards Manager will guide you through the appropriate process to finalize and approve the new document.

 

TAPPI Standards and Technical Information Papers (TIPs) will have a booth at TAPPI Central at the upcoming PaperCon 2013 conference in Atlanta, April 28-May 1, 2013. TAPPI Central will be located in the Hyatt Regency Atlanta Hotel on the Ballroom Level in the pre-function area outside the "Learning Center."

The purpose of the Standards and TIPs booth is to generate interest in participation in the development and review of these very important documents. We are also looking for ideas for new topics to cover. If you are coming to PaperCon 2013, please stop by the booth, where you can give us feedback on what new topics need to be addressed. You can see copies of the current Standards and TIPs that are coming up for review in 2013, and you also can sign up on site to join the Standard-Specific Interest Groups (SSIGs) for Standards review or the working groups for TIP review.

 

A proposal has been made for a new standard test method: "Laboratory simulation of tail-edge pick."

The scope of the method is: This test method covers a procedure used to simulate the tail-edge wet pick phenomenon in laboratory conditions. The purpose is to determine the degree of tail-edge pick of coated papers. This test method encompasses the relation to fountain solution and print dynamic interactions with the printing ink and coated paper surface.

A Standard-Specific Interest Group (SSIG) must be formed for this proposal. Any individuals who are interested in this Standard may join the SSIG to receive ballots when this method is ready for vote.

This announcement originally ran in the February STAR, but not enough people have joined the SSIG (10 is the minimum). The deadline to respond has been extended to April 30, 2013. If you would like to join the SSIG for this project, please notify the Standards Department at standards@tappi.org or by fax at +1-770-446-6947.

 

The system for review and development of TAPPI Standards requires an announcement of review dates so that any interested TAPPI parties may access the drafts, submit comments, and/or join the Standard-Specific Interest Group (SSIG) to cast an official vote.

Listed below are the Standards that will be up for review in 2013. The date indicated is the target date on which the draft will be posted for review by TAPPI members in the Members Only section of the TAPPI website. On that date, you may go to the home page (www.tappi.org), log on with your member ID and password, place your cursor over "Membership," and select "My TAPPI" from the dropdown box. When your personal page appears, click on the "Standards Public Draft Review" link on the left-hand side. You do not have to be a member of the Standard Specific Interest Group to comment on the draft.

Nonmembers of TAPPI who wish to be part of the voting for any Standard should send a message to standards@tappi.org and request voting membership on the corresponding SSIG, prior to the target ballot date, if possible. Anyone who joins the SSIG before the target balloting date will receive a notice of the ballot. Nonmembers cannot access the drafts online, but they will be sent copies by email upon request after receiving the notice of ballot by email.

If you have joined the Standard Specific Interest Group for any Standard, you will receive a notice for ballot at the proper time with instructions for casting your vote and making your comments. If you wish to join the Standard Specific Interest Group for a particular Standard, please go to the Subject Categories for Standards page or contact the Standards Department at TAPPI (standards@tappi.org ), or phone +1-770-209-7276 or fax +1-770-446-6947).

T 526 cm-04 Blister resistance of coated paper in heatset printing (May 7, 2013)
T 627 om-09 Determination of titanium dioxide (May 14, 2013)
T 648 om-09 Viscosity of coating clay slurry (May 21, 2013)
T 843 om-09 Fluted edge crush of corrugating medium (rigid support method) (June 4, 2013)
T 824 om-09 Fluted edge crush of corrugating medium (flexible beam method) (June 11, 2013)
T 836 om-09 Bending stiffness, four point method (June 18, 2013)
T 825 om-09 Flat crush test of corrugated board (rigid support method) (June 25, 2013)
T 569 om-09 Internal bond strength (Scott type) (July 9, 2013)
T 831 om-09 Water absorption of corrugating medium: water drop penetration test (July 16, 2013)
T 631 om-09 Microbiological enumeration of process water and slush pulp (July 23, 2013)
T 604 om-09 Sulfur dioxide in sulfite cooking liquor (July 30, 2013)
T 1205 sp-09 Dealing with suspect (outlying) test determinations (August 6, 2013)
T 529 om-09 Surface pH measurement of paper (August 13, 2013)
T 650 om-09 Solids content of black liquor (August 20, 2013
T 699 om-09 Analysis of pulping liquors by suppressed ion chromatography (September 10, 2013)
T 534 om-09 Brightness of clay and other mineral pigments (d/0 diffuse) (September 24, 2013)
T 515 om-09 Visual grading and color matching of paper (October 1, 2013)
T 480 om-09 Specular gloss of paper and paperboard at 75 degrees (October 8, 2013)
T 458 cm-04 Surface wettability of paper (angle of contact method) (October 15, 2013)
T 573 sp-09 Accelerated temperature aging of printing and writing paper by dry oven exposure apparatus (October 22, 2013)
T 409 sp-09 Machine direction of paper and paperboard (October 29, 2013)
T 448 om-09 Water vapor transmission rate of paper and paperboard at 23 degrees C and 50% RH (November 5, 2013)
T 455 sp-09 Identification of wire side of paper (November 12, 2013)
T 278 sp-09 Pulp screening (Valley-type screening device) (November 19, 2013)
T 227 om-09 Freeness of pulp (Canadian standard method) (December 3, 2013)
T 259 om-09 Species identification of nonwood plant fibers (December 10, 2013)

 

The next meeting of the Standards Advisory Review Group (SARG) is scheduled for Tuesday, April 30, 2013, 1:30 pm EASTERN time, at the Hyatt Regency Hotel in Atlanta, GA (the site of the 2013 PaperCon Conference).

SARG approval is the last step prior to publication for any new or revised standard. In order to act on any appeals from TAPPI members relevant to the standards up for approval, the SARG meeting is open to anyone for participation. The agenda was posted on the SARG page at least 50 days prior to the meeting, in accordance with TAPPI’s guidelines. There are links from the agenda items to the final drafts that are up for approval. If you would like to participate in the SARG meeting by conference call, please send a message before April 25, 2013, to standards@tappi.org.

 

Reports outlining the overdue reviews for Standards and TIPs were sent to the Quality and Standards Management Committee (Q&SMC) on February 22, 2013. Copies of these reports were also sent to the assigned Working Group Chairmen for these overdue reviews as well as to chairmen of the appropriate technical groups in TAPPI. Anyone who did not receive the overdue reports but who have an interest may obtain copies by requesting them from standards@tappi.org.

Working Group Chairmen: These reports were sent to you for your information and action, if required. Q&SMC may, according to the Standards Guidelines, withdraw any Standards or TIPs whose reviews are overdue, especially if it appears that little progress is being made on the Work Item. If more information or indications of progress on these Work Items are received prior to the next meeting (April 30, 2013),

To provide updates regarding these reports, send a message to to standards@tappi.org no later than Thursday, April 25, 2013, in order to be able to provide this information to Q&SMC at their next meeting.

 

For details on these commonly-used acronyms in the development of TAPPI Standards and TIPs, please see the Standards Guidelines and the TIP Guidelines, or send your questions to standards@tappi.org.

TIP = Technical Information Paper
Q&SMC = Quality and Standards Management Committee
SSIG = Standard-Specific Interest Group
SARG = Standards Advisory Review Group
WI = Work Item
WG = Working Group
WGC = Working Group Chairman
om = Official Method
pm = Provisional Method
sp = Standard Practice
cm = Classical Method
ss = Standard Specification
sg = Standard Guideline
gl = Standard Glossary
wd = Withdrawn Standard
UM = Useful Method

 

Details on how to search and order TAPPI Standards, TIPs and Useful Methods can be found on the TAPPI website's Search and Order page.

For Individual TIPs, order Item Number: 0108____ (Insert TIP number)

For Individual Standards, order Item Number: 0104T____ (Insert Standard number)

For individual Useful Methods, order Item Number 0104UM____ (insert UM number)

List price: $49; TAPPI member price: $32. There are no shipping or handling charges for electronic documents.

The 2013 collection of Standards, TIPs, and UMs, published in March of 2013 (product code STUCD-13), is available on CD. An Individual or Company License for access to the continually updated collection of Standards, TIPs, and UMs via the web is the best way to always have a current set of documents accessible. A print-on-demand version of either the Standards, TIPs, or UMs, current and updated as of the date printed, is also available.

For information and quotes on company licenses, contact Jeff Wellsat jwells@tappi.org or +1-770-209-7228. For regular orders (including individual online licenses), contact Member Connection at 1-800-332-8686 (US), 1-800-446-9431 (Canada), or +1-770-446-1400 (international), or order on line at www.tappi.org.