Print this article  Send to Colleague
The Standards listed below are due for an upcoming review in 2019. If you wish to participate in the SSIGs that will review these Standards or if you would like to request a copy of the drafts in ballot, please send your request to the Standards Administrator, at standards@tappi.org.
APRIL T 200 sp15 Laboratory beating of pulp (Valley beater method) T 213 om15 Dirt in pulp  chart method T 248 sp15 Laboratory beating of pulp (PFI mill method) T 259 om15 Species identification of nonwood plant fibers T 401 om15 Fiber analysis of paper and paperboard T 409 sp15 Machine direction of paper and paperboard T 454 om15 Turpentine test for voids in glassine and greaseproof papers T 546 om15 Machinedirection grammage variation measurement (gravimetric method) T 555 om15 Roughness of paper and paperboard (printsurf method) T 558 om15 Surface wettability and absorbency of sheeted materials using an automated contact angle tester T 563 om15 Equivalent black area (EBA) and count of visible dirt in pulp, paper and paperboard by image analysis T 573 sp15 Accelerated temperature aging of printing and writing paper by dry oven exposure apparatus T 650 om15 Solids content of black liquor T 1007 sp15 Sample location for fiber glass mat sheets T 1012 om15 Moisture content of fiber glass mats T 1015 sp 15 Fiber glass mat uniformity (visual defects) MAY T 254 cm10 Cupriethylenediamine disperse viscosity of pulp (falling ball method) T 431 cm10 Ink absorbency of blotting paper T 617 cm10 Analysis of lime T 619 cm10 Analysis of salt cake T 1008 sp15 Test conditions for fiberglass mat test methods OCTOBER T 222 om15 Acid insoluble lignin in wood and pulp T 223 cm10 Pentosans in wood and pulp T 261 cm10 Fines fraction by weight of paper stock by wet screening T 403 om15 Bursting strength of paper T 411 om15 Thickness (caliper) of paper, paperboard, and combined board T 429 cm10 Alphacellulose in paper T 434 cm10 Acidsoluble iron in paper T 456 om15 Tensile breaking strength of watersaturated paper and paperboard (“wet tensile strength”) T 480 om15 Specular gloss of paper and paperboard at 75 degrees T 489 om15 Bending resistance (stiffness) of paper and paperboard (Tabertype tester in basic configuration) T 493 cm10 Identification and determination of melamine resin in paper T 509 om15 Hydrogen ion concentration (pH) of paper extracts (cold extraction method) T 534 om15 Brightness of clay and other mineral pigments (d/0 diffuse) T 541 om15 Internal bond strength of paperboard (zdirection tensile) T 553 om15 Alkalinity of paper as calcium carbonate (alkaline reserve of paper) T 566 om15 Bending resistance (stiffness) of paper (Tabertype tester in 0 to 10 Taber stiffness unit configuration) T 567 om15 Determination of effective residual ink concentration (ERIC) by infrared reflectance measurement T 600 om15 Analysis of formaldehyde in aqueous solutions and of free formaldehyde in resins T 610 sp15 Preparation of indicators and standard solutions T 613 cm10 Analysis of caustic soda T 618 cm10 Analysis of limestone T 621 cm10 Analysis of rosin T 622 cm10 Analysis of sodium hydrosulfite T 628 cm10 Analysis of rosin size T 684 om15 Gross heating value of black liquor T 803 cm10 Puncture test of containerboard T 829 om15 Score quality test T 844 pm15 Determining construction (nominal basis weight) of corrugated board T 1006 sp15 Testing of fiber glass mats: use of modified TAPPI procedures for sampling and lot acceptance, stiffness, tear resistance, air permeability, and thickness T 1011 om15 Basis weight of fiber glass mats T 1013 om15 Loss on ignition of fiber glass mats T 1014 om15 Moisture sensitivity of fiber glass mats T 1016 om15 Average fiber diameter of fiber glass mats
You may find the list of the Standards coming up for review at TAPPI website: http://www.tappi.org/GetInvolved/DevelopStandardsMethods/StandardsSchedule/
